Korenix JetNet 7852G-4XG Series User Manual Download Page 1445

Page: 1445 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1445/1568

11.6.10.4

Configuring VRRP Interface Tracking

Configurable Data

Priority Decrement

- The priority decrement for the tracked interface. The valid range is 1 -

254. default value is 10.

Remove

- Removes the selected Tracking interface from the VRRP tracked list.

Non-Configurable Data

Interface

- The interface for which data is to be displayed.

Virtual Router ID

- The Virtual Router ID for which data is to be displayed.

S.No

- The serial number for this row.

Tracking Interface

- The Tracked interface for which data is to be displayed or configured.

Interface State

- The IP state of the tracked interface.

Command Buttons

Add

- Proceed to the VRRP Track interface screen.

Submit

- Send the updated configuration to the router. Configuration changes take effect

immediately. These changes will not be retained across a power cycle unless a save is
performed.

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

Cancel

- Return to the Virtual Router Configuration screen.

«
...
1443
1444
1445
1446
1447
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands