manualshive.com logo in svg

Korenix JetNet 7852G-4XG Series, User Manual

The Korenix JetNet 7852G-4XG Series switch offers high performance and reliability for industrial networks. Find the user manual for free download on our website for easy configuration and setup. Gain access to detailed instructions and troubleshooting tips to optimize performance. Download your manual at manualshive.com.

Share
Download
background image

Korenix Technology Co., Ltd.                                           

 

Industrial

 

Layer 3 Managed Ethernet Switch

 

 
 

_____________________________________________________________________________ 

Industrial Layer 3 Managed Ethernet SwitchUser Manual

 

 Page: 1040/1568 

Web Mode 

- Specify whether the switch may be accessed from a Web browser. If you choose to 

enable web mode you will be able to manage the switch from a Web browser. The factory default is 
enabled. 

 

Java Mode 

- Enable or disable the java applet that displays a picture of the switch at the top right of 

the screen. If you run the applet you will be able to click on the picture of the switch to select 
configuration screens instead of using the navigation tree at the left side of the screen. The factory 
default is enabled. 

 

IPv4 Configurable Data

 

 

IP Address 

- The IP address of the interface. The factory default value is 0.0.0.0 

 

Subnet Mask 

- The IP subnet mask for the interface. The factory default value is 0.0.0.0 

 

Default Gateway 

- The default gateway for the IP interface. The factory default value is 0.0.0.0 

Management VLAN ID 

- 

Specifies the management VLAN ID of the switch. It may be configured to 

any value in the range of 1 - 4093. The management VLAN is used for management of the switch. 
This field is configurable for administrative users and read-only for other users. 

 

Web Port 

- This field is used to set the HTTP Port Number. The value must be in the range of 1 to 

65535. Port 80 is the default value. The currently configured value is shown when the web page is 
displayed. 

 

 

IPv4 Non-Configurable Data

 

 

Burned In MAC Address 

- The burned in MAC address used for in-band connectivity if you choose 

not to configure a locally administered address. 

 

IPv6 Selection Criteria

 

 

IPv6 Mode - 

Enable/Disable IPv6 Admin Mode. 

 

Network Configuration Protocol - 

Enable or Disable DHCPv6 Client protocol on the management 

port. The factory default is None. 

 

IPv6 Stateless Address AutoConfig Mode - 

Enable or Disable the IPv6 stateless address 

autoconfiguration on the management port. By default it is disabled. 

 

Add/Delete IPv6 Addresses - 

To Add or Delete the IPv6 Addresses, select Add or Remove from the 

drop-down menu. The fields "New IPv6 Address" and "EUI Flag" are visible when we select the "Add" 
from this menu. 

 

EUI Flag - 

To set the EUI flag while configuring "New IPv6 Address" select TRUE from the drop down 

menu. Default is FALSE. 

 

Change IPv6 Gateway - 

Select the checkbox to configure/change IPv6 Gateway Addresses. 

 

 

IPv6 Configurable Data

 

 

DHCPv6 Client DUID 

- Displays the Client Identifier used by DHCPv6 Client when sending 

messages to the DHCPv6 Server. This entry is visible to user only if IPv6 Network Configuration 
Protocol is set to DHCP. 

 

New IPv6 Address - 

To configure the field, select Add from the "Add/Delete IPv6 Addresses" drop 

down menu. 

 

IPv6 Address to Delete - 

To configure the field, select Remove from the "Add/Delete IPv6 

Addresses" drop down menu. 

 

IPv6 Gateway - 

The default gateway for the IPv6 Interface. 

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

D-Link DES-7200 User Manual preview
DES-7200
Brand: D-Link Pages: 100
D-Link DES-3226L Manual preview
DES-3226L
Brand: D-Link Pages: 134
D-Link DES-3010F Command Line Interface Manual preview
DES-3010F
Brand: D-Link Pages: 187
D-Link DES-3010F Manual preview
DES-3010F
Brand: D-Link Pages: 225
D-Link DES-1048G Manual preview
DES-1048G
Brand: D-Link Pages: 31
D-Link DES-1050G User Manual preview
DES-1050G
Brand: D-Link Pages: 35
D-Link DES-1016D - Switch Quick Install Manual preview
DES-1016D - Switch
Brand: D-Link Pages: 19
D-Link COVR-2202 User Manual preview
COVR-2202
Brand: D-Link Pages: 107
D-Link AirPlusXtremeG DI-624 Troubleshooting preview
AirPlusXtremeG DI-624
Brand: D-Link Pages: 5
D-Link DGS-1210-28P Getting Started Manual preview
DGS-1210-28P
Brand: D-Link Pages: 48
GE MDS SD Series Setup Manual preview
MDS SD Series
Brand: GE Pages: 4
Oracle B31003-01 User Manual preview
B31003-01
Brand: Oracle Pages: 112
Hanwha Techwin Wisenet PRN-6400B4 Quick Manual preview
Wisenet PRN-6400B4
Brand: Hanwha Techwin Pages: 14
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Brand: Orolia Pages: 167
FiberHome AN5506-04-F User Manual preview
AN5506-04-F
Brand: FiberHome Pages: 2
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
Planet FGSW-2620 User Manual preview
FGSW-2620
Brand: Planet Pages: 13
Thecus N2520 series User Manual preview
N2520 series
Brand: Thecus Pages: 130

Brands by name

Popular brands

Load more brands