Korenix JetNet 7852G-4XG Series User Manual Download Page 400

Page: 400 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 400/1568

6.9.4.69

Captive Portal error message indicating authentication timeout

This command is to Captive Portal configuration error message indicating authentication timeout.

Syntax

timeout-msg <UTF-16>

no timeout-msg

Default Setting

None

Command Mode

Captive Portal Locale Mode

6.9.4.70

Captive Portal text for main title

This command is to Captive Portal configuration text for main title.

Syntax

title-text <UTF-16>

no title-text

Default Setting

None

Command Mode

Captive Portal Locale Mode

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands