Korenix JetNet 7852G-4XG Series User Manual Download Page 1338

Page: 1338 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1338/1568

used. Valid range is (1 to 4294967295).

Non-Configurable Data

Interface

- Displays selected interface.

Direction

- Displays selected packet filtering direction for ACL.

ACL Type

- Displays the type of ACL assigned to selected interface and direction.

ACL Identifier

- Displays the ACL Number(in case of IP ACL) or ACL Name(in case of MAC ACL)

identifying the ACL assigned to selected interface and direction.

Sequence Number

- Displays the Sequence Number signifying the order of specified ACL relative

to other ACLs assigned to selected interface and direction.

Command Buttons

Submit

- Send the updated configuration to the switch. Configuration changes take effect

immediately. These changes will not be retained across a power cycle unless a save is performed.

Remove

- Removes the currently selected ACL Interface Direction Mapping from the switch

configuration.

«
...
1336
1337
1338
1339
1340
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands