Korenix JetNet 7852G-4XG Series User Manual Download Page 1483

Page: 1483 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1483/1568

11.7.7.6

Viewing OSPFv3 Interface Statistics Page

This screen displays statistics for the selected interface. The information will be displayed only if
OSPFv3 is enabled.

Selection Criteria

Interface

- Select the interface for which data is to be displayed.

Non-Configurable Data

OSPFv3 Area ID

- The OSPFv3 area to which the selected router interface belongs. An OSPFv3

Area ID is a 32 bit integer in dotted decimal format that uniquely identifies the area to which the
interface connects.

«
...
1481
1482
1483
1484
1485
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands