Korenix JetNet 7852G-4XG Series User Manual Download Page 222

Page: 222 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 222/1568

6.3.6.3

snmp trap link-status

This command enables link status traps by interface.

This command is valid only when the Link Up/Down Flag is enabled. See

‘snmpserver

enable traps linkmod

e’ command.

Syntax

snmp trap link-status
no snmp trap link-status

no -

This command disables link status traps by interface.

Default Setting

Disabled

Command Mode

Interface Config

This command enables link status traps for all interfaces.

This command is valid only when the Link Up/Down Flag is enabled. See

‘snmpserver

enable traps linkmod

e’ command.

Syntax

snmp trap link-status all
no snmp trap link-status all

all -

All interfaces.

no -

This command disables link status traps for all interfaces.

Default Setting

Disabled

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands