Korenix JetNet 7852G-4XG Series User Manual Download Page 889 | Manualshive

Page: 889 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 889/1568

8.4.2.2

ip mcast boundary

This command adds an administrative scope multicast boundary specified by <groupipaddr> and
<mask> for which this multicast administrative boundary is applicable. <groupipaddr> is a group IP
address and <mask> is a group IP mask.

Syntax

ip mcast boundary <groupipaddr> <mask>
no ip mcast boundary <groupipaddr> <mask>

<groupipaddr> -

the multicast group address for the start of the range of addresses to be

excluded. The address must be in the range of 239.0.0.0 through 239.255.255.255.

<mask> -

mask to be applied to the multicast group

address.

no -

This command deletes an administrative scope multicast boundary specified by

<groupipaddr> and <mask> for which this multicast administrative boundary is applicable.
<groupipaddr> is a group IP address and <mask> is a group IP mask.

Default Setting

No
ne

Command Mode

Interface
Config

«
...
887
888
889
890
891
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

EtherLink 3C509B

Brand: 3Com Pages: 8

TokenLink 3C359B

Brand: 3Com Pages: 4

TokenLink 3C359B

Brand: 3Com Pages: 8

TokenLink 3C339

Brand: 3Com Pages: 2

EtherLink 3C985B-SX

Brand: 3Com Pages: 44

Brand: 3Com Pages: 88

Brand: 3Com Pages: 2

Brand: 3Com Pages: 111

TokenLink 3C359

Brand: 3Com Pages: 4

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: Qualys Pages: 2

Brand: Google Pages: 14

Brand: Teac Pages: 20

cMT-FHDX Series

Brand: Maple Systems Pages: 2

Brand: NETGEAR Pages: 2

BIC 1I12-P2A25-M30MI1-BPX05-110

Brand: Balluff Pages: 12

EonServ 5000 Series

Brand: Surveon Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands