Korenix JetNet 7852G-4XG Series User Manual Download Page 1031

Page: 1031 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1031/1568

11.2.1.3

System Resources

Use this panel to configure and display the Free Memory and Task CPU Utilization parameters

Configurable Data

Rising Threshold

- The CPU Rising utilization threshold in percentage. A zero percent threshold

indicates CPU Utilization Notification feature is disabled.

Rising Threshold Interval

- The CPU Rising threshold interval in seconds. The time interval is

configured in multiples of 5. A time interval of zero seconds indicates CPU Utilization Notification
feature is disabled.

Free Memory Threshold

- The CPU Free Memory threshold in kilobytes. A zero threshold value

indicates CPU Free Memory Notification feature is disabled

Non- Configurable Data

Free Memory

- Available Free Memory on system in kilobytes.

Alloc Memory

- Allocated Memory for the system in kilobytes.

Task Id

- Id of the Currently Running Tasks.

Task Name

- Name of the Currently Running Tasks.

5 Seconds

- Percentage of CPU utilized by the corresponding task in the last 5 seconds.

60 Seconds

- Percentage of CPU utilized by the corresponding task in the last 60 seconds.

300 Seconds

- Percentage of CPU utilized by the corresponding task in the last 300 seconds.

Total CPU Utilization

- Total CPU Utilization in terms of Percentage over a period of 5, 60, 300

seconds, and the Rising threshold period also in seconds, if configured.

«
...
1029
1030
1031
1032
1033
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands