Korenix JetNet 7852G-4XG Series User Manual Download Page 1539

Page: 1539 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1539/1568

11.8.10

Viewing IPv4 Multicast Static MRoute Table Summary

This page is used to summarize the configured static mroute entries.

Configurable Data

Remove

- Check Box to Delete the Selected Static MRoute Entry.

Non-Configurable Data

Source IP

- The address of the Multicast data source.

Source Mask

- The network mask for the IP address of the Multicast data source to be configured.

RPF Next Hop

- The RPF Address for the source range of static mroute entry.

Preference

- The preference with which the static mroute to be considered against other

matching static mroute entry for a given source.

Command Buttons

Delete

- Deletes the selected static mroute entries in the router. This is used to delete the

entries selected using the Checkbox under Remove field

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

«
...
1537
1538
1539
1540
1541
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands