Korenix JetNet 7852G-4XG Series User Manual Download Page 803

Page: 803 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 803/1568

Prefixes Current:

Number of prefixes current kept.

Prefixes Accepted:

Number of prefixes accepted.

Prefixes Rejected:

Number of prefixes rejected.

Max NLRI per Update:

Maximum number of network layer reachability attributes in UPDATEs.

Min NLRI per Update:

Minimum number of network layer reachability attributes in UPDATEs.

Inbound:

Received from the peer.

Outbound:

Transmitted to the peer.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands