Korenix JetNet 7852G-4XG Series User Manual Download Page 471

Page: 471 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 471/1568

6.13.2.10

lldp med confignotification

The user can go to the CLI Interface Configuration Mode to set all the ports to send the topology change
notification, use the

lldp med confignotification

Interface configuration command. Use the

no lldp med

confignotification

to disable notifications.

Syntax

lldp med confignotification
no lldp med confignotification

Default Setting

Disabled

Command Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands