Korenix JetNet 7852G-4XG Series User Manual Download Page 1118 | Manualshive

Page: 1118 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1118/1568

11.2.12.4

Viewing LLDP Statistics Page

Non-Configurable Data

Last Update

- Specifies the time when an entry was created, modified or deleted in the tables

associated with the remote system.

Total Inserts

- Specifies the number of times the complete set of information advertised by a

particular MAC Service Access Point (MSAP) has been inserted into tables associated with the
remote systems.

Total Deletes

- Specifies the number of times the complete set of information advertised by a

particular MAC Service Access Point (MSAP) has been deleted from tables associated with the
remote systems.

Total Drops

- Specifies the number of times the complete set of information advertised by a

particular MAC Service Access Point (MSAP) could not be entered into tables associated with the
remote systems because of insufficient resources.

Total Ageouts

- Specifies the number of times the complete set of information advertised by a

particular MAC Service Access Point (MSAP) has been deleted from tables associated with the
remote systems because the information timeliness interval has expired.

Interface

- Specifies the slot/port for the interfaces.

Transmit Total

- Specifies the number of LLDP frames transmitted by the LLDP agent on the

corresponding port.

Receive Total

- Specifies the number of valid LLDP frames received by this LLDP agent on the

corresponding port, while the LLDP agent is enabled.

Discards

- Specifies the number of LLDP TLVs discarded for any reason by the LLDP agent on the

corresponding port.

Errors

- Specifies the number of invalid LLDP frames received by the LLDP agent on the

corresponding port, while the LLDP agent is enabled.

Ageouts

- Specifies the number of age-outs that occurred on a given port. An age-out is the number

of times the complete set of information advertised by a particular MAC Service Access Point (MSAP)
has been deleted from tables associated with the remote entries because information timeliness
interval had expired.

TLV Discards

- Specifies the number of LLDP TLVs discarded for any reason by the LLDP agent on

the corresponding port.

TLV Unknowns

- Specifies the number of LLDP TLVs received on the local ports which were not

«
...
1116
1117
1118
1119
1120
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: TDC Pages: 27

MatrixPRO-II DVI 16x16

Brand: Barco Pages: 43

Brand: Barco Pages: 5

Brand: WaiLan Pages: 27

Brand: iBall Baton Pages: 9

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

Brand: Teknim Pages: 10

Brand: Toto Link Pages: 55

SLK-R602 Series

Brand: Seriallink Pages: 29

Brand: Eneo Pages: 68

PSoC 4 S Series

Brand: Cypress Pages: 4

XC-16CH-NVR-4TB

Brand: Xyclop Pages: 19

Brand: Patton electronics Pages: 8

Brand: LevelOne Pages: 49

Brand: PRIZM Pages: 8

Brand: Deliberant Pages: 16

Network Adapter ADZIFCF

Brand: Addonics Technologies Pages: 1

Brand: Juniper Pages: 396

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands