Korenix JetNet 7852G-4XG Series User Manual Download Page 1472

Page: 1472 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1472/1568

Valid LifeTime (Sec)

- The valid life time (in seconds) of the IPv6 Address leased by the DHCPv6

Server.

Renew Time (Sec)

- The time remaining (in seconds) to send a DHCPv6 Renew request to DHCPv6

Server for the leased address.

Expiry Time (Sec)

- The time (in seconds) when the DHCPv6 leased address expires.

Statistic

DHCPv6 Advertisement Packets Received

- Number of DHCPv6 Advertisement packets received

on the selected interface.

DHCPv6 Reply Packets Received

- Number of DHCPv6 Reply packets received on the selected

interface.

Received DHCPv6 Advertisement Packets Discarded

- Number of DHCPv6 Advertisement

packets discarded on the selected interface.

Received DHCPv6 Reply Packets Discarded

- Number of DHCPv6 Reply packets discarded on

the selected interface.

DHCPv6 Malformed Packets Received

- Number of DHCPv6 packets that are received malformed

on the selected interface.

Total DHCPv6 Packets Received

- Total number of DHCPv6 packets received on the selected

interface.

DHCPv6 Solicit Packets Transmitted

- Number of DHCPv6 Solicit packets transmitted on the

selected interface.

DHCPv6 Request Packets Transmitted

- Number of DHCPv6 Request packets transmitted on the

selected interface.

DHCPv6 Renew Packets Transmitted

- Number of DHCPv6 Renew packets transmitted on the

selected interface.

DHCPv6 Rebind Packets Transmitted

- Number of DHCPv6 Rebind packets transmitted on the

selected interface.

DHCPv6 Release Packets Transmitted

- Number of DHCPv6 Release packets transmitted on the

selected interface.

Total DHCPv6 Packets Transmitted

- Total number of DHCPv6 packets transmitted on the

selected interface.

Command Buttons

Refresh

- Refreshes the data on the screen with the present state of the data in the switch.

«
...
1470
1471
1472
1473
1474
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands