Korenix JetNet 7852G-4XG Series User Manual Download Page 189

Page: 189 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 189/1568

6.3.1.4

interface vlan

This command is used to enter Interface-vlan configuration mode.

Syntax

interface vlan <vlanid>

<vlanid> -

VLAN ID (Range: 1 - 4093).

Default Setting

None

Command Mode

Global Config

6.3.1.5

ip address

This command sets the IP Address, and subnet mask. The IP Address and the gateway must be on the
same subnet.

Syntax

ip address <ipaddr> <netmask>
no ip address

<ipaddr> -

IP address

<netmask> -

Subnet Mask

no -

Restore the default IP address and Subnet Mask

Default Setting

IP address: 0.0.0.0

Subnet Mask: 0.0.0.0

Command Mode

Interface-Vlan Config

Command Usage

Once the IP address is set, the VLAN ID

’s value will be assigned to management VLAN.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands