Korenix JetNet 7852G-4XG Series User Manual Download Page 80

Page: 80 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 80/1568

6.2.2.8

show mac-address-table stats

This command displays the MFDB statistics.

Syntax

show mac-address-table stats

Default Setting

None

Command Mode

Privileged Exec

Display Message

Max MFDB Table Entries:

This displays the total number of entries that can possibly be in the

MFDB.

Most MFDB Entries Since Last Reset:

This displays the largest number of entries that have been

present in the Multicast Forwarding Database table. This value is also known as the MFDB
high-water mark.

Current Entries:

This displays the current number of entries in the Multicast Forwarding Database

table.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands