Korenix JetNet 7852G-4XG Series User Manual Download Page 1194

Page: 1194 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1194/1568

11.3.15

Managing GARP

11.3.15.1

Configuring the whole Switch GARP Configuration Page

It can take up to 10 seconds for GARP configuration changes to take effect.

Configurable Data

GVRP Mode

- Choose the GARP VLAN Registration Protocol administrative mode for the switch by

selecting enable or disable from the pull down menu. The factory default is disabled.

GMRP Mode

- Choose the GARP Multicast Registration Protocol administrative mode for the switch

by selecting enable or disable from the pull down menu. The factory default is disabled.

Command Buttons

Submit

- Update the switch with the values you entered. If you want the switch to retain the new

values across a power cycle you must perform a save.

«
...
1192
1193
1194
1195
1196
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands