Korenix JetNet 7852G-4XG Series User Manual Download Page 1557

Page: 1557 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1557/1568

interface is Operational.

Interface Neighbors

Neighbor Count

- The number of PIM neighbors on the selected interface. This field is

displayed only when the interface is Operational.

Neighbor IP Address

- The IP address of the PIM neighbor for this entry.

Uptime

- The time (in hours:minutes:seconds) since this PIM neighbor (last) became a neighbor

of the local router.

Expiry Time

- The minimum time (in hours:minutes:seconds) remaining before this PIM

neighbor will be aged out.

Command Buttons

Refresh

- Refresh the data on the screen with the present state of the data in theswitch.

«
...
1555
1556
1557
1558
1559
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands