Korenix JetNet 7852G-4XG Series User Manual Download Page 1137 | Manualshive

Page: 1137 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1137/1568

Unicast Packets Transmitted Rate

- The total number of packets rates that higher-level protocols

requested be transmitted to a subnetwork-unicast address, including those that were discarded or
not sent.

Multicast Packets Transmitted Rate

- The total number of packets rates that higher-level protocols

requested be transmitted to a Multicast address, including those that were discarded or not sent.

Broadcast Packets Transmitted Rate

- The total number of packets rates that higher-level

protocols requested be transmitted to the Broadcast address, including those that were discarded or
not sent.

Discarded Packets Transmitted Rate

- The number of outbound packets rates which were chosen

to be discarded even though no errors had been detected to prevent their being deliverable to a
higher-layer protocol. A possible reason for discarding a packet could be to free up buffer space.

Errors Transmitted Rate

- The errors transmitted rate of Single, Multiple, and Excessive Collisions.

Time Since Counters Last Cleared

- The elapsed time, in days, hours, minutes, and seconds since

the statistics for this port were last cleared.

Command Buttons

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

«
...
1135
1136
1137
1138
1139
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: D-Link Pages: 12

Brand: Magnat Audio Pages: 2

Brand: US Robotics Pages: 36

Brand: Idis Pages: 31

NI WLS/ENET-9163

Brand: National Instruments Pages: 36

Brand: SyChip Pages: 24

Net2Air Ins-40085-US

Brand: Paxton Pages: 4

Brand: ZyXEL Communications Pages: 215

SmartMesh IA-510 D2511

Brand: Dust Networks Pages: 30

Brand: Draytek Pages: 2

Brand: Genie Pages: 6

Brand: NKE Pages: 15

ExpressBox2 EB2

Brand: Magma Pages: 74

BiPAC 5200S RC Series

Brand: Billion Pages: 79

FiberTwist XGS2410

Brand: Genexis Pages: 7

Brand: Helmholz Pages: 14

Brand: e+p Pages: 2

Brand: ADTRAN Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands