Korenix JetNet 7852G-4XG Series User Manual Download Page 1436 | Manualshive

Page: 1436 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1436/1568

11.6.8.3

Configuring (Static) Routes Entry

Selection Criteria

Route Type

- This field can be either default or static or static reject. If creating a default route, all

that needs to be specified is the next hop IP address, otherwise each field needs to be specified.

Configurable Data

Network Address

- The IP route prefix for the destination.

Subnet Mask

- Also referred to as the subnet/network mask, this indicates the portion of the IP

interface address that identifies the attached network.

Next Hop IP Address

- The outgoing router IP address to use when forwarding traffic to the next

router (if any) in the path towards the destination. The next router will always be one of the adjacent
neighbors or the IP address of the local interface for a directly attached network.

Metric

- Administrative cost of the path to the destination. If no value is entered, default is 1. The

range is from 0 to 255.

Preference

- Specifies a preference value for the configured next hop.

Command Buttons

Add Route

- Go to a separate page where a route can be created.

«
...
1434
1435
1436
1437
1438
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: D-Link Pages: 32

Brand: D-Link Pages: 6

Brand: D-Link Pages: 221

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

Express Ethernetwork DI-707P

Brand: D-Link Pages: 14

Brand: Lorex Pages: 186

Brand: TRENDnet Pages: 2

Barricade SMC7901WBRA2

Brand: SMC Networks Pages: 2

Brand: IDT Pages: 207

Brand: Wave Wireless Networking Pages: 167

B-Control Fader BCF2000

Brand: Behringer Pages: 13

Brand: M-system Pages: 4

Brand: Kramer Pages: 56

Brand: Kasda Pages: 39

Brand: CopperOptics Pages: 12

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

Brand: NetComm Pages: 75

Brand: Proscend Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands