Korenix JetNet 7852G-4XG Series User Manual Download Page 1439

Page: 1439 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1439/1568

11.6.9.2

Viewing VLAN Routing Summary Information

Non-Configurable Data

VLAN ID

- The ID of the VLAN whose data is displayed in the current table row

Slot/Port

- The Slot/Port assigned to the VLAN Routing Interface

MAC Address

- The MAC Address assigned to the VLAN Routing Interface

IP Address

- The configured IP Address of the VLAN Routing Interface. This will be 0.0.0.0 when the

VLAN Routing Interface is first configured and must be entered on the IP Interface Configuration
page.

Subnet Mask

- The configured Subnet Mask of the VLAN Routing Interface. This will be 0.0.0.0

when the VLAN Routing Interface is first configured and must be entered on the IP Interface
Configuration page.

«
...
1437
1438
1439
1440
1441
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands