Korenix JetNet 7852G-4XG Series User Manual Download Page 1127

Page: 1127 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1127/1568

11.2.13.3

Configuring LLDP-MED Interface Summary Page

Non-Configurable Data

Interface

- Specifies all the ports on which LLDP-MED can be configured.

Link Status

- Specifies the link status of the ports whether it is Up/Down.

MED Status

- Specifies the LLDP-MED mode is enabled or disabled on this interface.

Operational Status

- Specifies the LLDP-MED TLVs are transmitted or not on this interface.

Notification Status

- Specifies the LLDP-MED topology notification mode of the interface.

Transmit TLV(s)

- Specifies the LLDP-MED transmit TLV(s) that are included.

Command Buttons

Refresh

- Updates the information on the page.

«
...
1125
1126
1127
1128
1129
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands