Korenix JetNet 7852G-4XG Series User Manual Download Page 330

Page: 330 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 330/1568

6.9.1.10

show dot1x users

This command displays 802.1x port security user information for locally configured users.

Syntax

show dot1x users <slot/port>

<slot/port> -

is the desired interface number.

Default Setting

None

Command Mode

Privileged Exec

Display Message

User:

Users configured locally to have access to the specified port.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands