Korenix JetNet 7852G-4XG Series User Manual Download Page 939

Page: 939 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 939/1568

9.2.2

Configuration Commands

9.2.2.1

interface loopback

This command uses to enter the Interface Config mode for a loopback interface. The range of

the loopback ID is 0 to 7.

Syntax

interface loopback <0-7>
no interface loopback <0-7>

no -

This command removes the loopback interface and associated configuration parameters for the

specified loopback interface.

Default Setting

Disabled

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands