Korenix JetNet 7852G-4XG Series User Manual Download Page 814

Page: 814 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 814/1568

7.11.2.3 aggregate-address

Use

aggregate-address

command to create an aggregate entry in a Border Gateway Protocol (BGP)

database. Use

no aggregate-address

command to disable an aggregate entry in a Border Gateway

Protocol (BGP) database.

Syntax

aggregate-address <address> <mask> [as-set] [summary-only]
no aggregate-address <address> <mask> [as-set] [summary-only]

address -

Aggregate address.

mask -

Aggregate mask.

as-set -

Generates autonomous system set path informatio.

summary-only -

Filters all more-specific routes from update.

Default Setting

The atomic aggregate attribute is set automatically when an aggregate route is created with this
command unless the as-set keyword is specified.

Command Mode

Router BGP Config Mode

7.11.2.4 bgp aggregate-different-meds

Use

bgp aggregate-different-meds

command to allow aggregation of routes with different MED values.

Use

no bgp aggregate-different-meds

command to disable this function.

Syntax

bgp aggregate-different-meds
no bgp aggregate-different-meds

Default Setting

Disabled

Command Mode

Router BGP Config Mode

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands