Korenix JetNet 7852G-4XG Series User Manual Download Page 1341

Page: 1341 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1341/1568

11.4.7.15

Access Control List VLAN ACL Summary Page

Non-Configurable Data

Summary Display Selector

- Select interface or VLAN to display summary. By default summary of

Interface-based ACL(s) is displayed.

Interface

- The interfaces to which the IP ACL applies.

VLAN(s)

- VLAN(s) to which the IP ACL applies.

Direction

- The direction of packet traffic affected by the IP ACL.

Direction can only be one of the following:



Inbound



Outbound

ACL Type

- Displays the type of ACL assigned to selected VLAN and direction.

ACL ID

- Displays the ACL Number(in case of IP ACL) or ACL Name(in case of IPv6 ACL and MAC

ACL) identifying the ACL assigned to selected VLAN and direction.

Sequence Number

- Displays the Sequence Number signifying the order of specified ACL relative

to other ACLs assigned to selected VLAN and direction.

Command Buttons

Refresh

- Refresh the data on the screen to the latest state.

«
...
1339
1340
1341
1342
1343
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands