Korenix JetNet 7852G-4XG Series User Manual Download Page 361

Page: 361 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 361/1568

6.9.3.9

dot1x re-authentication

This command enables re-authentication of the supplicant for the specified port.

Syntax

dot1x re-authentication
no dot1x re-authentication

no -

This command disables re-authentication of the supplicant for the specified port.

Default Setting

Disabled

Command Mode

Interface Config

6.9.3.10

dot1x supplicant max-start

This command configure the maximum number of Start EAPOL messages to be sent in the absence of
Authenticator.

Syntax

dot1x supplicant max-start <1-10>
no dot1x supplicant max-start

Default Setting

Command Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands