Korenix JetNet 7852G-4XG Series User Manual Download Page 1414

Page: 1414 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1414/1568

Redistribute

- Enables or disables the redistribution for the selected source protocol. It has to

be enabled to be able to configure any of the route redistribution attributes except the 'Distribute
List' field. Default value is Disable.

Command Buttons

Submit

- Send the updated configuration to the router. Configuration changes take

effect immediately.

Delete

- Delete the entry of the Source Route selected as Configured Source from the list of

Sources configured for OSPF Route Redistribution.

«
...
1412
1413
1414
1415
1416
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands