Korenix JetNet 7852G-4XG Series User Manual Download Page 818

Page: 818 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 818/1568

7.11.2.11 exit

This command is used to exit bgp configuration mode.

Syntax

exit

Default Setting

None

Command Mode

Router BGP Config Mode

7.11.2.12 timers bgp

This command is used to set the keepalive and holdtime timers. To return the router to default operation,
use the no form of this command.

Syntax

timers bgp <keepalive> <holdtime>
no timers bgp

keepalive

: The number of seconds this BGP speaker waits for a keepalive message before deciding

that the connection is down. We recommend you configure the

keepalive

parameter as 1/3 of the

holdtime

parameter.

holdtime

: The number of seconds this BGP speaker waits for a keepalive, update, or notification

message before deciding that the connection is down. We recommend you configure the holdtime
parameter as 3 times the keepalive parameter.

Default Setting

The default value of

keepalive

is 60 seconds.

The default value of

holdtime

is 180 seconds.

Command Mode

Router BGP Config Mode

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands