Korenix JetNet 7852G-4XG Series User Manual Download Page 876

Page: 876 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 876/1568

Querier Up Time:

Time elapsed in seconds since the querier state has been updated.

Querier Expiry Time:

Time left in seconds before the Querier loses its title as querier.

Wrong Version Queries:

Indicates the number of queries received whose MLD version does not

match the MLD version of the interface.

Number of Joins:

The number of times a group membership has been added on this interface.

Number of Leaves:

The number of times a group membership has been removed on this interface.

Number of Groups:

The current number of membership entries for this interface.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands