Korenix JetNet 7852G-4XG Series User Manual Download Page 1509

Page: 1509 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1509/1568

State

- The state of the specified neighbor router on the selected interface, either active or down.

Neighbor Uptime

- The DVMRP uptime for the specified neighbor on the selected interface. This

is the time since the neighbor entry was learned.

Neighbor Expiry Time

- The DVMRP expiry time for the specified neighbor on the selected

interface. This is the time left before this neighbor entry will age out, and is not applicable if
the neighbor router's state is down.

Generation ID

- The DVMRP generation ID for the specified neighbor on the selected interface.

Major Version

- The DVMRP Major Version for the specified neighbor on the selected

interface.

Minor Version

- The DVMRP Minor Version for the specified neighbor on the

selected interface.

Capabilities

- The DVMRP capabilities of the specified neighbor on the

selected interface.

Received Routes

- The number of routes received for the specified neighbor on the

selected interface.

Received Bad Packets

- The number of invalid packets received for the specified neighbor on

the selected interface.

Received Bad Routes

- The number of invalid routes received for the specified neighbor on

the selected interface.

Command Buttons

Refresh

- Refresh the data on the screen with the present state of the data in the switch..

«
...
1507
1508
1509
1510
1511
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands