Korenix JetNet 7852G-4XG Series User Manual Download Page 1161 | Manualshive

Page: 1161 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1161/1568

11.3.3.3

Configuring DHCP Snooping Interface Configuration Page

Selection Criteria

Interface

- Selects the interface for which data is to be displayed or configured.

Configurable Data

Trust State

- If it is Enabled DHCP snooping application considers as port trusted. The factory

default is disabled.

Logging Invalid Packets

- If it is Enabled DHCP snooping application logs invalid packets on this

interface. The factory default is disabled.

Rate Limit

- Specifies rate limit value for DHCP Snooping purpose. If the incoming rate of DHCP

packets exceeds the value of this object for consecutively burst interval seconds, the port will be
shutdown. If this value is None, there is no limit. The factory default is 15pps (packets per second).
The range of Rate Limit is (0 to 300).

No Limit

- Selecting this option specifies that the value of Rate Limit will be configured to -1. If the

rate limit is -1 burst interval has no meaning, hence it is disabled.

Burst Interval

- This Specifies the burst interval value for rate limiting purpose on this interface. If

the rate limit is None burst interval has no meaning shows it as N/A. The factory default is 1 second.
The range of Burst Interval is (1 to 15).

Command Buttons

Submit

- Applies the new configuration and causes the changes to take effect. These changes will

not be retained across a power cycle unless a save configuration is performed.

«
...
1159
1160
1161
1162
1163
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: D-Link Pages: 32

Brand: D-Link Pages: 6

Brand: D-Link Pages: 221

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

Express Ethernetwork DI-707P

Brand: D-Link Pages: 14

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 32

FIELDPOINT FP-1600

Brand: National Instruments Pages: 8

Brand: NETGEAR Pages: 2

Brand: LogLogic Pages: 30

Brand: Mercusys Pages: 35

NJ220 - IntelliJack Switch

Brand: 3Com Pages: 82

Conel UR5i v2 Libratum

Brand: B&B Electronics Pages: 32

Brand: EnGenius Pages: 3

4-Port 10/100Mbps Ethernet Broadband Router

Brand: AOpen Pages: 41

PCH1 T P Series

Brand: Parker Pages: 107

Brand: 4G Systems Pages: 2

Brand: XtendLan Pages: 228

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands