Korenix JetNet 7852G-4XG Series User Manual Download Page 625

Page: 625 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 625/1568

6.24.2.4

queue cos-queue strict

This command activates the strict priority scheduler mode for each specified queue on a "per-port" basis.

Syntax

queue cos-queue strict <queue-id-0> [<queue-id-1>

…

<queue-id-6>]

no queue cos-queue strict <queue-id-0> [<queue-id-1>

…

<queue-id-6>]

no -

This command restores the default weighted scheduler mode for each specified queue on a

"per-port" basis.

Default Setting

None

Command Mode

Interface Config.

This command activates the strict priority scheduler mode for each specified queue on a device.

Syntax

queue cos-queue strict all <queue-id-0> [<queue-id-1>

…

<queue-id-6>]

no queue cos-queue strict all <queue-id-0> [<queue-id-1>

…

<queue-id-6>]

no -

This command restores the default weighted scheduler mode for each specified queue on a

device.

Default Setting

None

Command Mode

Global Config.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands