Korenix JetNet 7852G-4XG Series User Manual Download Page 662

Page: 662 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 662/1568

7.1.2.7

arp resptime

This command configures the ARP request response timeout.

Syntax

arp resptime <1-10>
no arp resptime

<1-10> -

The range of default response time is 1 to 10 seconds.

no -

This command configures the default response timeout time.

Default Setting

The default response time is 1.

Command Mode

Global Config

7.1.2.8

arp retries

This command configures the ARP count of maximum request for retries.

Syntax

arp retries <0-10>
no arp retries

<0-10> -

The range of maximum request for retries is 0 to 10.

no -

This command configures the default count of maximum request for retries.

Default Setting

The default value is 4.

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands