Korenix JetNet 7852G-4XG Series User Manual Download Page 1555 | Manualshive

Page: 1555 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1555/1568

11.9.2.3

Configuring Interfac

e’s PIM Configuration Page

Selection Criteria

Interface

- Select the interface for which data is to be displayed or configured.

Configurable Data

Admin Mode

- Select Enable or Disable to set the administrative status of PIM for the

specified interface in the router. The default is Disable.

Hello Interval (secs)

- Enter the time (in seconds) between the Transmission of which PIM Hello

messages on this interface. The valid values are from (0 to 18000) seconds. The default value is
30 seconds.

Join/Prune Interval (secs)

- Enter the frequency (in seconds) at which PIM Join/Prune

messages are transmitted on this PIM interface. This field is applicable for PIMSM only. The
valid values are from (0 to 18000) seconds. The default value is 60 seconds.

BSR Border

- Select enable or disable to set BSR border status on the selected interface. This

field is applicable for PIMSM only.

DR Priority

- Enter the DR priority for the selected interface. This field is applicable for PIMSM

only. The valid values are from (0 to -2) The default value is 1.

Command Buttons

Submit

- Send the updated configuration to the router. Configuration changes take effect

immediately. These changes will not be retained across a power cycle unless a save is
performed.

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

«
...
1553
1554
1555
1556
1557
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 2

BB-HCM381A - Network Camera

Brand: Panasonic Pages: 28

BB-HCM381A - Network Camera

Brand: Panasonic Pages: 2

DHI-NVR5224-24P-4KS2

Brand: Dahua Pages: 24

Brand: Qlogic Pages: 2

Brand: Qlogic Pages: 172

Ethernet Communication Module DVPEN01-SL

Brand: Delta Electronics Pages: 54

RIPWAVE 40-00460-00R

Brand: Navini Networks Pages: 35

ION 1200 Series

Brand: PaloAlto Networks Pages: 90

Brand: Toto Link Pages: 55

Marconi OMS 1200

Brand: Ericsson Pages: 136

Brand: ZyXEL Communications Pages: 5

Brand: 3Com Pages: 50

SRA311-008P8 Series

Brand: Divio Pages: 4

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Brand: LaCie Pages: 67

Brand: Comet Labs Pages: 11

Brand: Dataprobe Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands