manualshive.com logo in svg

Korenix JetNet 7852G-4XG Series, User Manual

The Korenix JetNet 7852G-4XG Series switch offers high performance and reliability for industrial networks. Find the user manual for free download on our website for easy configuration and setup. Gain access to detailed instructions and troubleshooting tips to optimize performance. Download your manual at manualshive.com.

Share
Download
background image

Korenix Technology Co., Ltd.                                           

 

Industrial

 

Layer 3 Managed Ethernet Switch

 

 
 

_____________________________________________________________________________ 

Industrial Layer 3 Managed Ethernet SwitchUser Manual

 

 Page: 464/1568 

6.13.1.12 

show lldp med remote-device detail

 

 

The user can go to the CLI Privilege Exec to d display detailed information about remote devices that 
transmit current LLDP-MED data to an interface on the system, use the 

show lldp med remote-device 

detail 

<slot/port> 

Privilege command. 

 

 

Syntax

 

 

show lldp med remote-device detail <slot/port> 

 
 

 

Default Setting

 

 

None 

 

Command Mode

 

 

Privileged Exec 

 

Display Message

 

 

Term Definition:

 

 

Capabilities

: Specifies the supported and enabled capabilities that was received in MED TLV on 

this port. 

 

MED Capabilities Supported

: Specifies supported capabilities that was received in MED TLV 

on this port. 

 

MED Capabilities Enabled: 

Specifies enabled capabilities that was received in MED TLV on 

this port. 

 

Device Class

: Specifies device class as advertised by the device remotely connected to the 

port. 

 

Network Policies 

Specifies if network policy TLV is received in the LLDP frames on this port. 

 

Media Policy Application Type: 

Specifies the application type. Types of application types are 

unknown, voicesignaling, guestvoice, guestvoicesignalling, softphonevoice, videoconferencing, 
streammingvideo, vidoesignalling. Each application type that is received has the VLAN id, 
priority, DSCP, tagged bit status and unknown bit status. A port may receive one or many such 
application types. If a network policy TLV has been receive on this port only then would this 
information be displayed. 

 

Vlan ID: 

Specifies the VLAN id associated with a particular policy type. 

Priority: 

Specifies the priority associated with a particular policy type. 

DSCP: 

Specifies the DSCP associated with a particular policy type. 

Unknown: 

Specifies the unknown bit associated with a particular policy type. 

 

Tagged: 

Specifies the tagged bit associated with a particular policy type. 

 

Inventory 

Specifies if inventory TLV is received in LLDP frames on this port. 

 

Hardware Rev: 

Specifies hardware version of the remote device.  

 

Firmware Rev: 

Specifies Firmware version of the remote device.  

 

Software Rev: 

Specifies Software version of the remote device.  

 

Serial Num: 

Specifies serial number of the remote device. 

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
Campbell NL115 Instruction Manual preview
NL115
Brand: Campbell Pages: 42
G-Technology G-DRIVE ev ATC Product Manual preview
G-DRIVE ev ATC
Brand: G-Technology Pages: 35
Danfoss TFX Installation And Operation Manual preview
TFX
Brand: Danfoss Pages: 61
Dahua Smart 1U Quick Start Manual preview
Smart 1U
Brand: Dahua Pages: 24
TP-Link ER8411 Installation Manual preview
ER8411
Brand: TP-Link Pages: 2
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
Hamlet HRDSL742 User Manual preview
HRDSL742
Brand: Hamlet Pages: 122
Cabletron Systems SmartSTACK ELS100-24TXM Installation And User Manual preview
SmartSTACK ELS100-24TXM
Brand: Cabletron Systems Pages: 117
XAVI Technologies Corp. X7822r User Manual preview
X7822r
Brand: XAVI Technologies Corp. Pages: 63
Ubiquiti PBE-M5-400-ISO Quick Start Manual preview
PBE-M5-400-ISO
Brand: Ubiquiti Pages: 28
DHD Power Cruiser 52/XR Manual preview
52/XR
Brand: DHD Power Cruiser Pages: 60
MCT MPU100ZW User Manual preview
MPU100ZW
Brand: MCT Pages: 12
Nexxt Amp300 Quick Installation Manual preview
Amp300
Brand: Nexxt Pages: 2
Idis DR-8516 Installation Manual preview
DR-8516
Brand: Idis Pages: 28
Alcatel-Lucent Broadband 700 MHz Brochure preview
Broadband 700 MHz
Brand: Alcatel-Lucent Pages: 8
DAPAudio Odin CL-4 Connect User Manual preview
Odin CL-4 Connect
Brand: DAPAudio Pages: 20
Westermo LRW-112 Series Manual preview
LRW-112 Series
Brand: Westermo Pages: 28

Brands by name

Popular brands

Load more brands