Korenix JetNet 7852G-4XG Series User Manual Download Page 1376 | Manualshive

Page: 1376 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1376/1568

11.5.5.5

Configuring CoS interface queue

Selection Criteria

Interface

- Specifies all CoS configurable interfaces. The option "Global" represents the most recent

global configuration settings. These may be overridden on a per-interface basis.

Queue ID

- Specifies all the available queues per interface(platform based).

Scheduler Type

- Specifies the type of scheduling used for this queue.

Scheduler Type can only be one of the following:



strict



weighted

Default value is weighted.

Queue Management Type

- Queue depth management technique used for queues on this

interface. This is only used if device supports independent settings per-queue.
Queue Management Type can only be:



taildrop

Default value is taildrop.

Configurable Data

Minimum Bandwidth Allocated

- Specifies the sum of individual Minimum Bandwidth values for all

queues in the interface. The sum cannot exceed the defined maximum (100). This value is
considered while configuring the Minimum Bandwidth for a queue in the selected interface.

Minimum Bandwidth

- Specifies the minimum guaranteed bandwidth allotted to this queue. Setting

this value higher than its corresponding Maximum Bandwidth automatically increases the maximum
to the same value. Default value is 0. Valid Range is (0 to 100) in increments of 1 . The value 0
means no guaranteed minimum. Sum of individual Minimum Bandwidth values for all queues in the
selected interface cannot exceed defined maximum (100).

Command Buttons

Restore Defaults for All Queues

- Restores default settings for all queues on the selected

interface.

«
...
1374
1375
1376
1377
1378
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

AirPlus DWL-810

Brand: D-Link Pages: 25

Brand: Lindy Pages: 4

Brand: Quectel Pages: 23

Brand: US Robotics Pages: 36

Brand: peplink Pages: 2

Brand: Tbus Pages: 25

Brand: Faderfox Pages: 10

Brand: Kohler Pages: 32

Brand: Talent Pages: 18

FrameSaver DSL 9788 Router

Brand: Paradyne Pages: 28

Brand: SriHome Pages: 12

PXI PXITM -1000

Brand: National Instruments Pages: 55

HiGain Line Unit HLU-388

Brand: PairGain Pages: 7

Brand: C&H Technologies Pages: 50

Passport 8608GTE

Brand: Nortel Pages: 10

Brand: Baileigh Pages: 20

Brand: TRENDnet Pages: 3

Brand: Opengear Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands