Korenix JetNet 7852G-4XG Series User Manual Download Page 1510

Page: 1510 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1510/1568

11.8.5.4

Viewing DVMRP Next Hop Summary

Non-Configurable Data

Source IP

- The IP address used with the source mask to identify the source network for this

table entry.

Source Mask

- The network mask used with the source IP address.

Next Hop Interface

- The outgoing interface for this next hop.

Type

- The next hop type. 'Leaf' means that no downstream dependent neighbors exist on

the outgoing interface. Otherwise, the type is 'branch'.

Command Buttons

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

«
...
1508
1509
1510
1511
1512
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands