Korenix JetNet 7852G-4XG Series User Manual Download Page 1117

Page: 1117 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1117/1568

11.2.12.3

Viewing LLDP Interface Summary Page

Non-Configurable Data

Interface

- Specifies all the ports on which LLDP - 802.1AB can be configured.

Link Status

- Specifies the Link Status of the ports whether it is Up/Down.

Transmit

- Specifies the LLDP - 802.1AB transmit mode of the interface.

Receive

- Specifies the LLDP - 802.1AB receive mode of the interface.

Notify

- Specifies the LLDP - 802.1AB notification mode of the interface.

Optional TLV(s)

- Specifies the LLDP - 802.1AB optional TLV(s) that are included.

Transmit Management Information

- Specifies whether management address is transmitted in

LLDP frames.

Command Buttons

Refresh

- Updates the information on the page.

«
...
1115
1116
1117
1118
1119
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands