Korenix JetNet 7852G-4XG Series User Manual Download Page 1124

Page: 1124 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1124/1568

11.2.12.8

Viewing LLDP Remote Device Summary Page

Non-Configurable Data

Local Interface

- Specifies the local port which can receive LLDP frames advertised by a remote

system.

Chassis ID

- Specifies the chassis component associated with the remote system.

Port ID

- Specifies the port component associated with the remote system.

System Name

- Specifies the system name of the remote system.

Remote Comparison

- Display the result of comparison between LLDP local and remote devices

information.

Command Buttons

Refresh

- Updates the information on the page.

Clear

- Clears LLDP Remote Device information received on all the interfaces.

«
...
1122
1123
1124
1125
1126
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands