Korenix JetNet 7852G-4XG Series User Manual Download Page 497

Page: 497 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 497/1568

6.17.1.13

clear ip filter

This command is used to clear all ip filter entries.

Syntax

clear ip filter

Default Setting

None

Command Mode

Privileged Exec

6.17.1.14

clear dot1x authentication-history

This command resets the 802.1x authenticaiton-history.

Syntax

clear dot1x authentication-history [slot/port]

<slot/port> -

is the desired interface number.

Default Setting

None

Command Mode

Privileged Exec

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands