Korenix JetNet 7852G-4XG Series User Manual Download Page 152

Page: 152 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 152/1568

6.2.9.10

ipv6 mld snooping querier vlan election participate

The user can go to the CLI Global Configuration Mode to set MLD snooping querier vlan election
participate mode, use the

ipv6 mld snooping querier vlan election-participate <vlanid>

global

configuration command. Use the

no ipv6 mld snooping querier vlan election participate <vlanid>

return to disable.

Syntax

ipv6 mld snooping querier vlan election participate <vlanid>
no ipv6 mld snooping querier vlan election participate <vlanid>

<vlanid>

- VLAN ID (Range: 1

– 4093).

Default Setting

Disabled

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands