Korenix JetNet 7852G-4XG Series User Manual Download Page 295

Page: 295 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 295/1568

This command disables logging to hosts.

Syntax

logging host remove <hostindex>

<hostindex> -

Index of the log server.

Default Setting

None

Command Mode

Globla Config

This command reconfigures the IP address of the log server.

Syntax

logging host reconfigure <hostindex> <hostaddress>

<hostindex> -

Index of the log server.

<hostaddress> -

New IP address of the log server.

Default Setting

None

Command Mode

Globla Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands