Korenix JetNet 7852G-4XG Series User Manual Download Page 1136 | Manualshive

Page: 1136 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1136/1568

11.2.14.5

Viewing sFlow Port Summary Page

Selection Criteria

Interface

- Selects the interface for which data is to be displayed or configured.

Non-Configurable Data

Interface

- The interface for which data is being displayed.

ifIndex

- This object indicates the ifIndex of the interface table entry associated with this port on an

adapter.

Octets Received Rate

- The total number of octets of data received rates by the processor

(excluding framing bits but including FCS octets).

Unicast Packets Received Rate

- The number of subnetwork-unicast packets rates delivered to a

higher-layer protocol.

Multicast Packets Received Rate

- The total number of packets received rates that were directed

to a multicast address. Note that this number does not include packets directed to the broadcast
address.

Broadcast Packets Received Rate

- The total number of packets received rates that were directed

to the broadcast address. Note that this does not include multicast packets.

Discarded Packets Received Rate

- The number of inbound packets which were chosen to be

discarded rates even though no errors had been detected to prevent their being deliverable to a
higher-layer protocol. A possible reason for discarding a packet could be to free up buffer space.

Errors Received Rate

- The errors received rate of Single, Multiple, and Excessive Collisions.

Unknown Protocols Packets Received Rate

- For packet-oriented interfaces, the number of

packets received rates via the interface which were discarded because of an unknown or
unsupported protocol. For character-oriented or fixed-length interfaces that support protocol
multiplexing the number of transmission units received via the interface which were discarded
because of an unknown or unsupported protocol. For any interface that does not support protocol
multiplexing, this counter will always be 0.

Octets Transmitted Rate

- The total number of octets transmitted rates out of the interface,

including framing characters.

«
...
1134
1135
1136
1137
1138
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: CAME Pages: 19

Brand: Icidu Pages: 10

Brand: M86 Security Pages: 46

Brand: Draytek Pages: 8

LinkSmart KW6515

Brand: Kasda Pages: 31

Brand: Eneo Pages: 68

Brand: Moxa Technologies Pages: 51

Brand: NC-link Pages: 20

Brand: NETGEAR Pages: 142

Brand: CalAmp Pages: 115

Brand: TP-Link Pages: 2

Brand: ADTRAN Pages: 161

Blue Gate ISDN BRI Brave

Brand: Alphatech Pages: 6

Brand: Comtrend Corporation Pages: 208

Brand: Dynamix Pages: 87

Brand: AIC Pages: 79

RouteFinder RF560VPN

Brand: Multitech Pages: 82

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands