Korenix JetNet 7852G-4XG Series User Manual Download Page 69

Page: 69 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 69/1568

no -

This command removes the advertised capability with using parameter

Default Setting

10G full-duplex for 10G SFP+ ports

1G full-duplex for 1G SFP ports

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands