Korenix JetNet 7852G-4XG Series User Manual Download Page 883

Page: 883 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 883/1568

8.4.1.2

show ip mcast boundary

This command displays all the configured administrative scoped multicast boundaries.

Syntax

show ip mcast boundary [{<slot/port> | vlan <vlan-id>}]

<slot/port > -

Interface number.

<vlan-id> -

VLAN ID. The range of VLAN ID is 1 to 4093.

no parameter -

Represents all interfaces.

Default Setting

None

Command Mode

Privileged

Exec User

Exec

Display Message

Interface:

Valid slot and port number separated by forward slashes.

Group IP:

The group IP address.

Mask:

The group IP mask.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands