Korenix JetNet 7852G-4XG Series User Manual Download Page 1262

Page: 1262 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1262/1568

11.4

Security Menu

11.4.1

Managing Access Control (802.1x)

11.4.1.1

Defining Access Control Page

Configurable Data

Administrative Mode

- This selector lists the two options for administrative mode: enable and

disable. The default value is disabled.

VLAN Assignment Mode

- This selector lists the two options for VLAN Assignment mode: Enable

and Disable. The default value is Disable.

Dynamic VLAN Creation Mode

- This selector lists the two options for Dynamic VLAN Creation

Mode: Enable and Disable. The default value is Disable.

Monitor Mode

- This selector lists the two options for Monitor Mode: Enable and Disable. The

default value is Disable. The feature monitors the dot1x authentication process and helps in
diagnosis the authentication failure cases.

Command Buttons

Submit

- Sends the updated screen to the switch and causes the changes to take effect on the

switch but these changes will not be retained across a power cycle unless a save is performed.

Cancel

- This resets the page to display the administrative mode that is currently configured by the

selected unit.

«
...
1260
1261
1262
1263
1264
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands