Korenix JetNet 7852G-4XG Series User Manual Download Page 1547

Page: 1547 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1547/1568

11.9.1.6

Viewing MLD Traffic Page

Non-Configurable Data

Valid MLD Packets Received

- The number of valid MLD packets received by the router.

Valid MLD Packets Sent

- The number of valid MLD packets sent by the router.

Queries Received

- The number of valid MLD queries received by the router.

Queries Sent

- The number of valid MLD queries sent by the router.

Reports Received

- The number of valid MLD reports received by the router.

Reports Sent

- The number of valid MLD reports sent by the router.

Leaves Received

- The number of valid MLD leaves received by the router.

Leaves Sent

- The number of valid MLD leaves sent by the router.

Bad Checksum MLD Packets

- The number of Bad Checksum MLD Packets received by

the router.

Malformed MLD Packets

- The number of Malformed MLD Packets received by the router.

Common Buttons

Refresh

- Refresh the data on the screen with the present state of the data in the router.

Clear Traffic

- Clears all the parameters for the selected interface.

«
...
1545
1546
1547
1548
1549
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands