manualshive.com logo in svg

Korenix JetNet 7852G-4XG Series, User Manual

The Korenix JetNet 7852G-4XG Series switch offers high performance and reliability for industrial networks. Find the user manual for free download on our website for easy configuration and setup. Gain access to detailed instructions and troubleshooting tips to optimize performance. Download your manual at manualshive.com.

Share
Download
background image

Korenix Technology Co., Ltd.                                           

 

Industrial

 

Layer 3 Managed Ethernet Switch

 

 
 

_____________________________________________________________________________ 

Industrial Layer 3 Managed Ethernet SwitchUser Manual

 

 Page: 927/1568 

8.8 

MLD Proxy Commands 

 

MLD-Proxy is the IPv6 equivalent of IGMP-Proxy. MLD-Proxy commands allow you to configure the 
network device as well as to view device settings and statistics using either serial interface or telnet 
session. The operation of MLD-Proxy commands is the same as for IGMP-Proxy: MLD is for IPv6 and 
IGMP is for IPv4.MGMD is a term used to refer to both IGMP and MLD. 

 
 
 

 

8.8.1 

Show Commands 

 

 

8.8.1.1   show ipv6 mld-proxy 

 

This command displays a summary of the host interface status parameters. 

 

 

Syntax

 

 

show ipv6 mld-proxy 

 
 

 

Default Setting

 

 

None 

 

Command Mode 

Privileged Exec 

User Exec 

Display Message

 

 

Interface index

: 

The interface number of the MLD-Proxy. 

 

Admin Mode: 

States whether the MLD-Proxy is enabled or not. This is a configured value. 

 

Operational Mode: 

States whether the MLD-Proxy is operationally enabled or not. This is a status 

parameter. 

 

Version: 

The present MLD host version that is operational on the proxy interface. 

 

Number of Multicast Groups: 

States the number of multicast groups that are associated with the 

MLD-Proxy interface. 

 

Unsolicited Report Interval: 

The time interval at which the MLD-Proxy interface sends unsolicited 

group membership report. 

 

Querier IP Address on Proxy Interface: 

The IP address of the Querier, if any, in the network 

attached to the upstream interface (MLD-Proxy interface). 

 

Older Version 1 Querier Timeout: 

The interval used to timeout the older version 1 queriers. 

 

Proxy Start Frequency: 

The number of times the MLD-Proxy has been stopped and started. 

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Paradyne 7610 Overview preview
7610
Brand: Paradyne Pages: 2
Qualys GUARD Quick Start Manual preview
GUARD
Brand: Qualys Pages: 2
FOR-A MFR-4000 Operation Manual preview
MFR-4000
Brand: FOR-A Pages: 72
Funkwerk TR 200 aw/ bw Operating Instructions preview
TR 200 aw/ bw
Brand: Funkwerk Pages: 2
Paradyne Comsphere 3510 User Manual preview
Comsphere 3510
Brand: Paradyne Pages: 85
Allied Telesis AR725 Quick Start Manual preview
AR725
Brand: Allied Telesis Pages: 22
Tbus NV-ER1816i Installation Manual preview
NV-ER1816i
Brand: Tbus Pages: 25
Faderfox 4midiloop User Manual preview
4midiloop
Brand: Faderfox Pages: 10
Mellanox Technologies ConnectX-3 Pro MCX349A-XCCN User Manual preview
ConnectX-3 Pro MCX349A-XCCN
Brand: Mellanox Technologies Pages: 35
BHU NETWORKS BXM2 User Manual preview
BXM2
Brand: BHU NETWORKS Pages: 75
IBM EtherLink XL User Manual preview
EtherLink XL
Brand: IBM Pages: 72
Ubiquiti EdgeRouter ER-8 Quick Start Manual preview
EdgeRouter ER-8
Brand: Ubiquiti Pages: 20
KYLAND Technology KIEN1009 Hardware Installation Manual preview
KIEN1009
Brand: KYLAND Technology Pages: 24
LevelOne NetCon FBR-1409TX User Manual preview
NetCon FBR-1409TX
Brand: LevelOne Pages: 88
Pullnet AGENT-2 S41D Line User Manual preview
AGENT-2 S41D Line
Brand: Pullnet Pages: 89
EMC VNX5300 Block Hardware Information Manual preview
VNX5300 Block
Brand: EMC Pages: 88
ZyXEL Communications Prestige 643 User Manual preview
Prestige 643
Brand: ZyXEL Communications Pages: 191
Allied Telesis Routers and Switches Datasheet preview
Routers and Switches
Brand: Allied Telesis Pages: 15

Brands by name

Popular brands

Load more brands