Korenix JetNet 7852G-4XG Series User Manual Download Page 816 | Manualshive

Page: 816 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 816/1568

7.11.2.7 bgp fast-external-failover

This command configures Border Gateway Protocol (BGP) routing process to immediately reset external
BGP peering sessions if the link used to reach these peers goes down.

no bgp fast-external-failover

command disables this function.

Syntax

bgp fast-external-failover
no bgp fast-external-failover

Default Setting

Enabled

Command Mode

Router BGP Config Mode

7.11.2.8 bgp fast-internal-failover

This command configures Border Gateway Protocol (BGP) routing process to immediately reset internal
BGP peering sessions if the link used to reach these peers goes down.

no bgp fast-internal-failover

command disables fast failover for internal peers.

Syntax

bgp fast-internal-failover
no bgp fast-internal-failover

Default Setting

Enabled

Command Mode

Router BGP Config Mode

«
...
814
815
816
817
818
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: Paradyne Pages: 16

Brand: Javad Pages: 35

Brand: Idis Pages: 86

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

ICS-G7748A Series

Brand: Moxa Technologies Pages: 10

Brand: Paradyne Pages: 10

Brand: NETGEAR Pages: 2

Brand: Perle Pages: 2

Brand: HELVAR Pages: 2

Brand: QuickLink Pages: 8

Brand: TP-Link Pages: 176

Brand: Xantech Pages: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Brand: Juniper Pages: 122

Brand: Hama Pages: 24

Brand: Black Box Pages: 62

Brand: XtendLan Pages: 17

Brand: Fibrain Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands