Korenix JetNet 7852G-4XG Series User Manual Download Page 323

Page: 323 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 323/1568

6.9.1.4

show dot1x

This command is used to show the status of the dot1x Administrative mode.

Syntax

show dot1x

Default Setting

None

Command Mode

Privileged Exec

Display Message

Administrative mode:

Indicates whether authentication control on the switch is enabled or disabled.

VLAN Assignment Mode

: Indicates whether assignment of an authorized port to a RADIUS

assigned VLAN is allowed (enabled) or not (disabled).

Dynamic VLAN Creation Mode

: Indicates whether the switch can dynamically create a

RADIUS-assigned VLAN if it does not currently exist on the switch.

Monitor Mode

: Indicates whether the Dot1x Monitor mode on the switch is enabled or disabled.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands